What to prepare before the production of woven cashmere

Apr 19, 2024

Leave a message

Woven cashmere is formed by the interweaving of warp and weft yarns on a loom. In the weaving process, longitudinal and transverse friction and bending occur repeatedly between the warp and the warp yarn, between the warp and the weft yarn, and between the warp yarn and various objects on the loom. In order to make the yarn have sufficient strength, wear resistance and elasticity, to ensure that the yarn will not be broken due to the action of the above-mentioned various destructive forces in the weaving process; in order to reduce the defects of the yarn, improve the finish, so as to ensure the weaving production efficiency, and obtain excellent products; in order to increase the length of the yarn package, which is conducive to continuous production, it is necessary to prepare the warp and weft yarn before weaving to improve the process performance of the warp and weft yarn.

1.Winding

The winding process is carried out on the winder. Its task is to connect the fine yarn obtained in the spinning project, in this process, to make the yarn obtain appropriate, uniform and consistent tension; according to the specified requirements, check and remove the yarn defects, impurities and dust chips such as coarse details on the yarn, and form a small and firm knot in the process of cleaning the defects; and wind into a package with uniform density, sufficient capacity, good forming, and easy to unwind.

2.Warpping

Warping is carried out on a warping machine. The task of the warping process is to draw out a piece of yarn from the package on the creel frame after the warping machine according to the number of warp threads specified in the process design, and according to the length and width specified in the design, in order to ensure that the tension between the yarn roots and roots, between pieces and sheets, and between the front and back is uniform, and under appropriate circumstances, the yarn pieces are wound into a well-formed warp beam in parallel.

3.Sizing

Sizing is a key process in the pre-weaving preparation and is carried out on the sizing machine. The task of the sizing process is mainly to improve the weaveability of the yarn, and at the same time, the yarn that has passed through the sizing is wound into a well-formed weaving shaft under the condition of uniform tension, uniform arrangement and uniform winding density. Improving the wovenability of the yarn is mainly manifested in three aspects: First, reinforcement - through the sizing, a slurry penetrates into the inside of the yarn, reducing the possibility of slippage between the fibers inside the yarn, thereby increasing the strength of the yarn and improving the ability to withstand tensile and impact loads. The second is to maintain the elasticity and elongation of the yarn in the process of sizing and drying, so as not to increase the breakage of the yarn during weaving due to brittleness and stiffness. The third is friction reduction - in sizing, a part of the slurry is covered on the surface of the yarn to form a slurry film, and the hairs on the surface of the yarn are attached to the yarn stem to reduce the friction coefficient between the yarn and between the yarn and the machine, and improve the ability of the yarn to resist friction.

4.Tying or knotting

This is the final step in the preparation of the warp weaving. The task of this process is to pass the yarn drawn out of the weaving shaft through the drop wire, heald eye and reed teeth one by one according to a certain rule according to the requirements of the designed fabric, so that it can be opened into a shed during weaving, incorporated into the weft, and woven into a fabric with a certain amplitude and warp density. The traditional drawing-in method is done by hand and with the help of semi-automatic machinery. When the batch of varieties produced is large, an automatic warping machine can be used to automatically connect the warp yarns on the new and old weaving shafts one by one to complete the drawing-in work.

5.Weft rolling

Weft winding is the weft preparation process before weaving. The main task is to rewind the weft package that has changed the shape of the package on the weft winding machine to make it that can meet the weaving requirements, have the appropriate density and good forming, uniform tension, easy to unwind, and meet the requirements of the package, and at the same time, remove a part of the yarn defects to improve the quality of the weft.

 

In the weaving process, when the weft tension is too small and the weft twist is large, or due to the strong weft twist force, it is possible to produce weft shrinkage and looping. In order to reduce or prevent the occurrence of malaise, in addition to reducing the weft twist and increasing the weft unwinding tension, the method of wetting and heating is often used to make the weft twisted.