What is the factory finishing process for ultra-thin worsted cashmere sweaters

May 11, 2024

Leave a message

Cashmere is known as "soft gold" because of its excellent wearing properties and lack of resources. It is one of the main raw materials for high-end clothing. For many years, cashmere products have been mostly used for spring and winter clothing. However, in recent years, with the diversified development of clothing and the advancement of textile technology, ultra-thin summer high-end knitted clothing made of worsted cashmere yarn knitted on flat knitting machines is lightweight and High-end, fashionable and unique style. Deeply loved by consumers. In order to ensure the style characteristics and appearance quality of this type of product, some improvements have been made to the finishing process.

1Example of production process

1.1 Product name

27.8 texx2, 12 G single-layer roll-neck single-sided round neck women's pullover.

1.2 Process flow

Sewing → Inspection → Collision → Lighting and repairing → Pre-shaping → Fulling → Drying → Lighting and repairing → Ironing and shaping → Ordering trademarks → Picking and inspecting → Packaging.

1.3 Process requirements

1.3.1 Suture

Use a 16G sewing disc machine and a 27.8 tex x2 garment raw material as the suture. The horizontal sewing consumption is 2 rows and the vertical sewing consumption is 2 needles. It is not allowed to have needles that are skewed or snagged when cuffing. The elongation rate of shoulder seams is greater than or equal to 110%, and the elongation rate of hem seams and sleeve bottom seams is greater than or equal to 130%. The upper collar should be round, the trocars at the oblique cuts of the collar should be even, and the needle pattern on the body should be straight. Dig down the back collar 1.5 to 2.0cm to prevent the back collar from floating up. The neckline seams are stretched 30cm.

1.3.2 Challenge

first. Remove the yarn from the collar and remove the loose loop, and repair the loose loop. Because the worsted yarn is strong, it is easy to tighten the coil and is difficult to repair. During the yarn removal process, do not use excessive force.

Use the taken off wool thread to sew the hem ribs and cuff ribs with alternate stitches. The beginnings of both sides should be flush. Reinforce the backstitch by 3 to 4 cm at the intersection of the hem seam and the bottom seam of the sleeves. The seam collar should be turned to the front and folded, and the longitudinal stitches should be aligned. If the seam exceeds 0.1 to 0.2 cm, each stitch must be backstitched.

1.3.3 Preforming

Worsted wool has a greater twist, and when the garment is knitted on the flat knitting machine to form loops, the yarn is subject to greater tension, resulting in greater internal stress. If the internal stress of the yarn is not well eliminated, the surface of the sweater will easily form unevenness and chicken claw marks during the washing and shrinking process, which will affect the appearance quality.

The specific method is to put the sweater on an ironing board of appropriate size and use a steam iron to evenly shape it. This process aims at a smooth surface, and the shaping conditions are the same as those after washing and shrinkage. Practice has proven that the surface smoothness of pre-shaped fleece sweaters is significantly improved, especially in single-sided fabrics.

1.3.4 Washing and shrinking

In order to maintain its smooth and smooth appearance, worsted cashmere sweaters are lightly milled. During the washing and shrinking process, the main purpose is decontamination to remove impurities produced during spinning and weaving, so that the methylene chloride soluble content of the sweater is less than 1.5%, and the sweater is given a bright color. However, cleaning and milling occur at the same time. Light and thin fleece sweaters are more prone to fluffing. It is contradictory to both wash and control fluffing. After many times of practice, the best process for washing and shrinking is to adopt a two-step method. The first step is to soak the cashmere sweater in a larger container with 1% detergent at a temperature of 25-30°C for 30 minutes, and then take it out for dehydration: the second step is to put the dried cashmere sweater into the SFNC2A type In the vertical milling machine, add 1% linseed oil, liquor ratio 1:20, temperature 38-40°C, and use intermittent rotation. Every 5 minutes of soaking, rotate for 5 seconds until 30 minutes, and then wash with clean water three times. Add 2% softener, temperature 45°C, liquor ratio 1:20, soak for 10 minutes every time, turn for 5 seconds until 20 minutes. Remove moisture and dry in time

1.3.5 Drying

When using the HG-757 cylindrical cage rotary hot air dryer, the temperature inside the machine should be controlled at 70 to 80°C. Cashmere rotates and rubs in hot air, and the fibers continue to fluff, so the drying time should be shortened as much as possible. The capacity of the cashmere sweater is set at 1/8 of the dryer capacity, and the completion time is controlled at 10 to 15 minutes.

1.3.6 Ironing and shaping

Make an ironing board according to the size of the finished product. Put the sweater on the ironing board. The steam pressure of the steam iron should reach 3.43x10 5 ~ 3.92x10 5 Pa. The distance between the iron and the sweater surface is 0.5 cm. (the shirt has no steam holes), iron it again at a uniform speed, then cool it, then take off the sweater and recycle the hem. After shaping, the cashmere sweater must have straight texture, a round neckline, no aurora, and meet the size requirements.

1.3.7 Cleaning and inspecting

Cashmere raw materials contain skin spots, foreign fiber and coarse hair, which affect the quality and appearance of cashmere sweaters. Cleaning out miscellaneous hair is an essential process for cashmere products. The lint picking tool can use adhesive paper and tweezers to stick the picked impurities to the paper, so as to avoid picking out burrs. Inspect finished product specifications as they are and package them in equal parts.

2 things to note

2.1 To make high-end cashmere sweaters, first of all, the process calculation must be precise, and the sewing process must be taken into account to ensure beautiful seams.

2.2 Due to the poor viscosity of the felt of worsted wool, the stitches should be small when the pick-and-roll head is reinforced, the head should be hidden stably, and the reinforcement should be firm to avoid exposing the wool head and opening seams.

2.3 Pre-shaping before washing can improve the surface smoothness of thin fleece sweaters and should be done strictly. The washing and shrinking process is an important process in the finishing process. Improper control can easily cause dead folds, chicken claw marks and excessive shrinkage. These defects are difficult to remove and affect the quality of the sweater.